Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
We have found this article pertaining to A Step-by-Step Guide to Installing a Bathtub below on the web and accepted it made good sense to talk about it with you on this page.
Installing a bathtub isn't precisely brain surgery, but it does require strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old tub is conveniently accessible, the project can move rapidly; if you need to open a wall surface to eliminate the old bathtub and place the new tub, the task is much harder. In either instance, the project is within a residence handyman's abilities, although you will require a helper to move out the old tub and also set in the brand-new one. Ensure you have actually qualified yourself for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed job, it is much better to consider employing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This short article will certainly aid you install a new tub in your washroom if you have already gotten a brand-new bathtub and don't need to transform the setup of your previous water supply pipes.
Your devices and also material checklist ought to make up the following:
Preparing for the Setup
First of all, the sustaining structure provided with the bath ought to be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable tap adapters to the bottom of both faucets using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the limited access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Tub
Making use of both wooden boards under its feet, position the bathtub in the called for position. The wooden boards are helpful in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub up until the level reads level.
To mount taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water system and inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Fill up the tub as well as also inspect the overflow electrical outlet and also the normal outlet for leakages.
Finally, repair the bath paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has actually been utilized at least once as this will resolve it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Safeguard the faucet in position with the maker offered backnut. Once the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former type should be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, creating the water to permeate the wall in between the bath and the tiling, resulting in complications with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and also cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can break fairly very early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about How to Install a Bathtub Yourself? Place feedback below. We'd be delighted to listen to your feelings about this write-up. Hoping that you visit us again later on. If you enjoyed reading our blog post kindly do not forget to pass it around. Thank-you for going through it.
Get A Free Estimate Report this page